Dear Customer;

Hello;

Thanking you for your good choice in terms of purchasing a tractor chassis that is manufactured in accordance with international standards and standards, we consider it necessary to ensure customer satisfaction and the fact that your machines are an investment fund for the development of agricultural mechanization and reduce The amount of crop production is a great contribution to our device under the warranty service. Your device is under the pre-delivery inspection (PDI) of ANECO, and will be delivered to you in accordance with the specifications of Case. Therefore, in terms of optimal use of the device, it requires that the device be set up, serviced and repaired in accordance with the written instructions and instructions of ANECO Company and Operator’s manual and trained operators. Your device will be covered by warranty service for 24 months or 2400 hours after delivery. Therefore, please, contact the nearest office location where you can find the warranty period in order to carry out the service and the warranty period. Please note that the provision of warranty service is subject to the following terms and conditions:

1. Your device requires three 50, 600 and 1200 hours service, which you must contact the nearest office location of the device before reaching the specified hours. Having this notebook is essential when performing the service and if it does not have any services, it will not be provided.
2. The cost of the above services includes the cost of mechanical wages, the responsibility of the company and its filters to the customer. (The customer is responsible for supplying the oil). These filters are delivered to the customers at the first, second and third service kits, and the customer is required to accompany them when they are present.
3. The provision of warranty services will be subject to the above services provided at specified times and by the authorized dealers of ANECO.
4. Apart from the above services to be provided by ANECO’s agents, the machine requires a daily service (or every 10 hours, each one arriving earlier) and a 50-hour service that you must provide in accordance with the training provided. Make relevant documentation and timely and register in the service booklet. The disadvantages caused by the failure to perform these services are not warranties.

5. Only the trained personnel have the operating license and the service and maintenance of the device. The operator must always have his or her training certificate. Disadvantages caused by an inappropriate operator or using untrained persons from the machine are not warranties.
6. All disadvantages and parts that are subject to the terms of the warranty will be repaired or replaced at no cost to ANECO’s agents. All repairs during the warranty period should only be made by ANECO authorized dealers. In case of a defect, contact the nearest ANECO representative immediately.
7. Service, regular maintenance of the machine, such as engine setting, fuel system cleaning, clutch and brake settings, etc., replacement of common parts and consumables such as filters, injectors, clutch and brake shoes, straps, glasses, lamps, fuses Parts that are in direct contact with the ground or product are not covered by the warranty. Also, the loss of jets, hoses and outer parts of the device that are lost due to normal use of the device or exposed to light are not covered by the warranty. It should be noted that the guaranty of the injector pump and tires is the responsibility of the manufacturer of the parts concerned.

8. In the event of any use of non-essential parts, as well as repairs by any person other than ANECO’s authorized dealers, the device is warranted. Also, parts that are inaccurately due to incorrect use, negligence, inaccuracy, or incident are not warranties.
9. ANECO will make changes and modifications to its products without any compulsion or modification in previously sold products.

10. In the aftermath of the warranty period, ANECO’s dealers will repair your device in accordance with factory recommendations and by technical, trained, and experienced personnel. ANECO’s network of agents can provide the most efficient and most economical way for you to repair.

1- Before starting up the machine , read all parts of the Operator’s Manual and then use it.

2. When servicing, repairing, adjusting, or operating the machine , follow the safety instructions in accordance with the contents of the Operator’s Manual and the provided tutorials.

3. Before performing the service, remove all parts of the actuator from the crank and remove the implement from the machine, and turn off the engine and pull the manual brake and remove the switch before leaving the cabin.
4. Perform a daily service (or 10 hours) and a 50-hour service in accordance with the contents of the maintenance and service booklet, the operator manual and the provided tutorials and complete the relevant forms. Warranty service warranties are subject to the accuracy and timely availability of these services and to be recorded in the service and maintenance booklet. So, be careful about the timely and timely delivery of these services.

5- Services of 50 – 600 and 1200 hours of the device must be made by authorized dealers ANECO. So contact the nearest dealer to contact the facility for at least two days before reaching the opening hours.

6. The presence of this office, along with the device and during the operation of the service and maintenance by the agent is necessary and without this booklet, no service is provided. So keep the notebook up to date and keep it intact to keep it clean.
7. Use the recommended lubricants and lubricants when servicing and servicing the machine.

8. Filter the exhaust air from the engine every day, depending on the type of weather in the area where you work, and if necessary, clean. The internal air filter engine acts as a safety filter and usually does not need to be cleaned and only replaced during service.
9. When the lighter lights up, stop the device and take the necessary steps in accordance with the operator’s manual.
10. Before opening the doors of the oil, water and fuel tanks, clean the door and the surrounding area thoroughly.
11. Always use clean fuel and free of any contamination and water. If you use a barrel to fill the fuel tank, first wait a while for fuel contamination and then fill up the fuel tank. Do not forget to drain some fuel from the bottom of the barrel containing impure impurities into the fuel tank.
12. Any welding on the machine is prohibited and, if necessary, contact ANECO’s authorized dealers. In the event of any non-standard welding, all tractor systems will be destroyed.
13. Use of water for washing the inside of the cabin and using high pressure water to clean the electric system, vents, bowls and covers.

14. If the battery is weak, never use an auxiliary battery, charge it, or replace it with a suitable battery.

15. Try to always deliver and consume the consumables of the device, including filters, belts, lubricants, lubricants, tools, etc. from ANECO’s dealerships.